NICE!

Very sweet setup there. :)

Thanks! It's taken time and sweat and tears of joy but it was worth it :p

My computer looks like **** in comparison.

Nice case, almost went with the K63 version.

Heres pics of the new GFX card that I am installing now. Cant wait to get the second one in.



Ill post pics of the build complete.

Actually that mobo does support CrossfireX, but not SLi. One slot runs in 16x and the other runs in 4x mode, but only if you specifically enable it in the BIOS, at the expense of both PCIe x1 slots and your front panel USB3 ports. I have an IP35 pro that has the 16x/4x config for Crossfire and it actually works really well. I've run a Crossfire setup in that board and the 4x slot doesn't really hold it back all that much. I guess that is the reason it doesn't support SLI though. They must require at least an 8x8x setup.

Here we can see one of the differences between the P8P67 Deluxe and the P8P67. The P8P67 only has two PCIe x16 expansion slots. The second of the PCIe x16 slots defaults to an x1 slot and must be adjusted to x4 in the BIOS to support AMD CrossfireX. Doing this does come at a cost, though, since the ASUS P8P67 doesn't have the added PCIe lanes that the PLX chip provides on the ASUS P8P67 Deluxe. Once the second PCIe x16 slot is enabled to x4 (default x1) both PCIe x1's and USB3 three and four (front panel USB3) will be disabled.

http://www.legitreviews.com/article/1500/4/

Glad you went and got a board with more features though, it'll do you well since you use nvidia cards right now.

If I could ever get the **** to work. Ive had so many problems with this build it's ridiculous.

Beleive it or not, those issues I were having was a SECOND fail GPU. I had a 570 GTX Zotac fail on me in the first week, took it back and got a 560 TI EVGA and it also failed!

So I went back to ATi. Ended up just going with 2x HIS 6870 1GBs for Crossfire. Here are the pics.


Here is the package before opening..




First sight after opening them.



After removing the accessory box from up top of the cards.



Letting them out to breath for the first time on their own.




Them in the case powered up (sorry these were cell shots the camera is dead and the cell camera HATES bright lights they are actually white LEDs and not blue..

sorry you're having such bad luck with GPU's, hope these work out better for you.

Lol its not your fault. On the positive side micro center took 20$ off each his for me. But then again I live about 25 miles from there so all the trips I'm sure I spent more in gas.

Wow, nice clean and fancy rigs. When I'll get my parts ordered and put together I'll take pics of my rat mod setup :lol:

IN GOES THE MAXIMUS Z
 

:evil:






Loving all the features. This board is crazyyyyyy. 4 usb 2 headers on the board and the led status lights, pcie switches. :eek::eek::eek: Turning the comp on with my iphone :heart::heart::heart:

Now to sell off the 5 week old GB P67-UD7-B3 :bleh:

That is a very sexy board!

Here is some better pics with the camera and not the cell.

That is a tight setup NYCDarkness. :drool:

The 600T does indeed look nice but a shame for me as something that white would look so out of place at my workstation lol!

Here's the latest revision of my rig, no more rv02 for me.

Sleeved cables :drool:

Same board, tri-sli, and no room for my sound card :(

I use a usb x-fi hooked to bose compaion 3s use to be ifi's till the amp in it died. While that's being fixed I picked up the compaion 3s for 170 on newegg shell shocker :D

Same here (usb x-fi); do you find that you loose sound randomly at times that requires a disconnect and then a reconnect of the usb?

Never. I do notice one thing though, it's not as good as my internal x-fi plat was. :bleh:

Very nicely done. how long did that take you?

Long enough lol considering first time around. Not something I would do again really unless I got really bored.

Man, that case looks amazing. Like something you'd find on a space shuttle. :drool:

Rewired my pc also replaced the 2 180mm fans at the bottom with Silverstone Air Penetrator 180mm fans (SST-AP181).















:drool:

Here's how the penetrator fans work:

My new el-cheapo rig. Going to post some pics of running computer tonight.









It has 3 120 mm fans, a nice 9900 Max Zalman to cool it down, cables are also well managed. My temps are hovering around 26 C ambient (case reports that), 45 C idle, 73 C load VC, 38 C idle and 53 C load comp and about 40 C a pop for the 3 HDDs.

Desktop
 

Lots of interesting systems shown in this thread. My own rig (Q9550/ASUS P5E in a Lian-Li PC-201B) has relatively poor cable management so it's nothing to write about. For me, it's always been about the displays:



30" Gateway in the lower middle, 2x20" Dell 2001FP on the lower left and right, 3x20" widescreens (2x Dell 2001WP, 1 LG) on the upper row. I use a HD6950 to drive the four left monitors and a HD4650 to drive the two on the right.

Yes I am a Nicole Kidman fan :D

Nice pics gents. Finally got my gigabyte p67a-ud7-b3 mobo back. Apparently newegg refused the rma due to physical damage. Think I must have damaged the proc pins when I placed the plastic cover back onto it after looking it over (not a smart move, I know). Gigabyte didn't replace it, but apparently repaired it.

Yeah, not a big fan of how easy you can damage the pins myself. I used to think you just had to be careful, which I am, but I managed to do it on my last return. Fortunately Newegg didn't catch it. The board's original issue wasn't the pins any how. So it was nice that they didn't come back on me and claim otherwise.

Good to hear that you ended up again with a working board. Hopefully it stays working well for you.

Speaking of, my original problem was that I had issues with my rimm slots. Slot 1 & 2 would not take modules, resulting in a reboot loop. Slots 3 & 4 were okay. Also, usb 3.0 would not work as well. Those were the two issues that prompted a rma. Just as likely of a culprit was the difficulty I had with my case and this mobo with the corsair h70. Might have forced the waterblock a little too much and caused the proc-pin issue? Guess I'll grab another 2600k and swap-out my x58 mobo on my amd system.